Plumbing Basics: The First Step for When Installing a Bathtub
Plumbing Basics: The First Step for When Installing a Bathtub
Blog Article
Just how do you actually feel on the subject of Installing A Bathtub?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably tough task. If the old tub is easily accessible, the job can relocate rapidly; if you have to open up a wall surface to remove the old bathtub and also place the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will need a helper to move out the old tub and embeded in the new one. See to it you have qualified yourself for the job and fit trying it. Rather than employing a service provider to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This article will certainly aid you install a new bathtub in your restroom if you have currently gotten a brand-new tub as well as don't require to transform the arrangement of your previous water system pipelines.
Your tools as well as product checklist must consist of the following:
Planning for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water system and also inspect all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has actually been used a minimum of once as this will certainly resolve it right into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous type should be attached to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to complications with dampness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make a remark down below. We will be interested to see your ideas about this blog posting. We are looking forward to see you back again in the near future. Enjoyed reading our write-up? Please share it. Help someone else discover it. I am grateful for your time. Please come by our website back soon.
Professional help? Ring! Report this page